Do you have orphan quilt blocks, leftover panel blocks, or paper-pieced blocks sitting around from other projects? Don’t let those extra blocks go to waste! Turn them into useful, heat-resistant potholders with this easy tutorial.
Almost any quilt block can become a potholder. I recently found some cute paper piecing patterns from Pen & Paper Quilts and decided to turn the blocks into potholders. You can do the same with leftover quilt blocks, orphan blocks, or individual blocks from a quilt panel.![From Quilt Block to Potholder Tutorial - fb]()
If the block is too small, simply add borders to make it larger. If it’s too big, trim it down or use it to make a larger potholder or trivet.
In this tutorial, I’ll show you how to turn a quilt block into a potholder, including how to layer and quilt the materials, trim the potholder, and add binding with a handy hanging loop.
For extra heat protection, these potholders use two layers of Insul-Bright along with one layer of batting. They’re a great way to give those unused quilt blocks a new purpose while making something useful for your kitchen.
Click the link below to watch our full tutorial on YouTube, or keep reading for the FREE photo tutorial.
PRINTABLE PDF TUTORIAL -
If you would like an ad free printable version of this tutorial optimized for printing, please visit our
Etsy Shop listing for Turn a Quilt Block into a Potholder #ad.
For a small fee, you can purchase a PDF downloadable version of this tutorial.
Keep reading for the free version of this tutorial.
COMPLETE VIDEO TUTORIAL AVAILABLE! The video below is a preview and may have no audio. To
watch the whole video tutorial, click the link Turn a Quilt Block into a Potholder to open it in Youtube.
Disclaimer: This post may contain affiliate links. We make a small commission on sales through the affiliate links, at no extra cost to you. Thank you in advance for your purchase and your support! Please see our full Affiliate
Statement for more information.
Foundation Paper-pieced block in samples
To make my potholders, I used Pen & Paper Patterns' FPP Nature Blocks. If you would like to make these blocks, you can purchase the pattern from their Etsy Shop.![Pen and Paper Pattern]()
These foundation paper pieced blocks are 5" square (4 1/2" square finished size). This is small for a potholder, so I added 1" and 1 1/2" borders to my blocks to make them larger than 7" square.
Follow this tutorial for more information!
Panel Quilt Block Samples
This project is perfect for using up individual blocks from a panel. I found these panel blocks in my stash and decided to pair them with a red binding. ![Panel Blocks]()
These panel blocks could be cut into 8" squares, so I didn't need to add borders. I used a panel block on each side, so no need for a backing fabric. Quick and easy! Here is one side. ![Coffee Panel Block Potholders Back]()
After quilting the layers, I trimmed them down to 7" squares. With the binding, they finished at a bit over 7" square. The photo below shows the other side.![Coffee Panel Block Potholders Front]()
Here is another set of potholders I made from panel blocks. These blocks were larger, so I cut them to 8" square. I used two panel blocks for each potholder and paired them with a coral-colored fabric for the binding.
Since these panel blocks were a little larger, I trimmed them to 7 1/2" squares after quilting the layers together. Some of the pictures were close to the border, so I trimmed more of the coral areas in order to keep the picture. ![Sea Creatures Panel Blocks Potholders]()
Feature Fabric Samples
I made these two potholders with chicken feature fabric. One is the normal 7" square size; the second is larger at about 10" square. The larger one will work as a trivet or potholder. ![Feature Fabric with Borders showing back]()
For the larger one, I cut the feature fabric into a 6 1/2" square. I cut the two borders at 1 1/4" and 1 1/2". Then I trimmed it to a 10" square before binding.
These are just some ideas! What kind of blocks will you use?
WHAT YOU NEED to make a potholder:
INSTRUCTIONS for turning a block into a potholder
Finished Size: Approximately 7" square (although you can make them any size you desire)
Seam Allowance: 1/4" unless otherwise specified
STEP 1: Pick a block
Select the block you would like to turn into a potholder. Keep in mind that a good finished size for potholders is 7" square.
Is your block smaller than 7"? No problem! I'll show you how to make it bigger.
Is your block larger than 7"? Check the block to see if you can trim it down to a 7" finished size. DON'T TRIM it yet! If you don't want to trim, you can make a larger potholder, 7"-10". Larger sizes work well for table trivets, too.
For this tutorial, I picked paper-pieced blocks that are 4 1/2" finished (5" pieced). I have selected two fabrics to add as borders to make the potholder larger. ![Block to Potholder 1 Fabrics and Finished Blocks]()
STEP 2: Blocks Larger than 7"
If the block is smaller than 7", skip to step 3.
For blocks that are larger than 7", trim them to a 7 1/2" square. We want them slightly larger than the finished size so you can trim them after quilting the layers together. During quilting, they can shrink or shift a bit, so it's good to have extra.
NOTE for PANEL BLOCKS: For the panel blocks, cut halfway between the blocks so you can use them all. I used one block on the front and back of the potholder, so cut two panel blocks. If they are smaller than 7 1/2", you can follow Step 3 to add a border.
If you'd like to make a larger block, cut your block 1/2" bigger than the finished size.
Skip to STEP 5.
STEP 3: Blocks Smaller than 7"
If your block is smaller than 7", add one or more borders to reach 7 1/2". You can make your potholder any size, so add borders so it's 1/2" larger than the desired finished size.
For my block, I added two borders cut at 1" and 1 1/2". Keep seam allowances in mind, and remember you are adding the border to two sides!
So, my block's finished size is 4 1/2". Adding the borders, minus the seam allowances, will be 4 1/2" + 1/2" + 1/2" + 1" + 1" = 7 1/2" (remember, you are adding a border to each side).![Block to Potholder 2 Cut Strips]()
To figure out the size of the borders to add, here are some calculations that can help:
Finished Size of Potholder: 7"
Size of Potholder with borders (before trimming): 7 1/2" (add 1/2" to the first #)
Current Size of your Block: 5"
Seam Allowances: 1/4"
How much do you need to add?
(Current Size of your Block) - 1/2" seam allowance) = Finished Block Size
((Size of Potholder with borders) - (Finished Block Size) ÷ 2 = Border Width
5" - 1/2" = 4 1/2"
(7 1/2" - 4 1/2") = 3"
3" ÷ 2 = 1 1/2"
How many Borders do you want to add?
1 Border = Border Width + 1/2" seam allowances = border cut width (1 1/2" + 1/2" = 2")
2 Borders = Pick the sizes of 2 borders that add up to your border width calculated above. For my example, I picked 1/2" and 1" = 1 1/2".
1st Border Width + 1/2" seam allowances = 1st Border Cut Width (1/2" + 1/2" = 1")
2nd Border Width + 1/2" seam allowances = 2nd Border Cut Width (1" + 1/2" = 1 1/2")
So, cut your borders at the calculated border cut width. I cut mine 1" and 1 1/2" by the width of the fabric (WOF).
STEP 4: Sew on the Borders
Sew the first border onto the block. First, sew on the two sides. Then sew the top and bottom.
To make it quick and easy, I did not cut each border to the size of the block. Take the first border fabric strip and place the raw edges along the side of the block. Overhang the beginning by 1/8"-1/4". The rest of the strip will hang off the end. Sew the seam.![Block to Potholder 3 Sew Two Sides]()
Use scissors to cut off the strip, leaving 1/8"-1/4" off the edge. Turn the block around and sew the border on the other side in the same way.
After sewing, you can use a ruler to square up the overhanging fabric. Honestly, I didn't bother to square it up. I just sewed on the next sides, keeping the fabric straight where it extended past the seam (see 2 photos down).
Press the seams towards the border fabric.![Block to Potholder 4 Iron Borders]()
Continue sewing on the first border to the top and bottom of the block in the same way. Notice in the photo below that I keep the fabric straight when sewing across the previous border.![Block to Potholder 5 add other sides]()
Press the last two seams towards the border.![Block to Potholder 6 Iron]()
Here is the block with the first borders added. Again, you can trim those overhanging borders, or go rogue with me and just sew on the next borders! We aren't making a whole quilt, so we don't need perfect points.![Block to Potholder 7 Block with First Border added]()
Sew the next two borders onto the sides as before. Press the seams towards the border. If you didn't trim the previous borders, just keep the fabric straight across the border.![Block to Potholder 8 Second Border]()
Sew the last two borders onto the top and bottom of the block and press the seams towards the border.![Block to Potholder 9 Second Border]()
Finally, square up the block to be 7 1/2" square. ![Block to Potholder 11 Squared Block]()
STEP 5: Cut the backing, batting & Insul-bright
Cut 8" squares (or 1/2" larger than your block size):
- 1 backing
- 1 cotton batting
- 2 Insul-Bright
NOTE for Panel Blocks: Cut the batting & Insul-bright to the size of your panel blocks, since you're using them on the front and back.![Block to Potholder 13 Insulbright Batting and Backing]()
STEP 6: Put the layers together
First, place the cotton batting between the two Insul-bright layers. ![Block to Potholder 14 Layer Insulbright and Batting]()
Lay the backing fabric, wrong side up, on a work surface.![Block to Potholder 15 Backing]()
Place the insulation layers on top.![Block to Potholder 16 Add Insulation layers]()
Then, center your quilt block on top.![Block to Potholder 17 Add Block]()
Pin the layers together with two pins. Iron all of the layers to remove some of the loft (fluffiness) from the potholder. This will be helpful when quilting.
Mark a diagonal line from corner to corner with your favorite marking method.![Block to Potholder 18 Pin Layers and mark diagonal line]()
NOTE for Panel Blocks: Many panel blocks have borders around them. Make sure they line up on both sides so the block looks even when trimmed. I placed a straight pin from front to back at each corner, making sure the pin goes through the border corner on both sides. I took the pin out just before stitching the first line of quilting.
STEP 7: Quilting the layers
Use a walking foot for this step. It will help all of the layers to feed evenly through the sewing machine.
I recommend using cotton thread. Cotton thread will stand up to the heat better than rayon or polyester blend thread. If your walking foot has a guide bar, put that on and adjust it to the desired width of the quilting lines.
For the potholder shown in the photo, I stitched the quilting lines 1/2" apart. For some of the others, I stitched lines 3/4" apart.
Start quilting by stitching along the marked line from corner to corner. Then work your way towards one corner, stitching lines using the guide to follow the previously stitched line.![Block to Potholder 19 Quilt Layers]()
Turn the potholder around and stitch the lines on the other side.![Block to Potholder 20 Quilted]()
STEP 8: Square up the potholder
Trim the potholder along the edge of the quilt block. This one is 7" square.
![Block to Potholder 22 Back]()
STEP 9: Bind the potholder
The potholder is ready to be bound and to have a hanging loop added. We have a video & photo tutorial on how to bind a potholder with a loop if you need more detailed instructions.
Cut a strip of fabric 2 1/2" by the width of the fabric. One strip should be enough for each potholder. Fold the strip in half lengthwise and press.![Block to Potholder 23 Binding]()
Sew the binding to the back of the potholder, starting on the top-left or top-right side. The hanging loop will be on the corner you start.![Block to Potholder Binding _1.56.1]()
Miter the corners. To miter, turn and stitch at a 45-degree angle into the corner.![Block to Potholder Binding _1.57.1]()
Then fold the binding back at the 45-degree angle and then down along the next side. ![Block to Potholder Binding _1.57.2]()
When you reach the first corner, flip the binding out and stop stitching before the binding. ![Block to Potholder Binding _1.59.1]()
Leave a 4" - 5" tail of fabric. This will be used to make the loop.
Flip the binding to the front and cover the previous stitching line. Stitch the binding down using a straight stitch close to the folded edge or a serpentine stitch. Fold and miter the corners. ![Block to Potholder Binding _2.2.1]()
Once you get back to the beginning, create a loop. Fold the seam allowance in. ![Block to Potholder Binding _1.64.1]()
Fold the binding over to cover the raw edge and continue stitching off the edge for about 4". ![Block to Potholder Binding _1.65.2]()
Fold the end over and decide the size of the loop. Then trim off the extra binding.![Block to Potholder Binding _1.67.1]()
Fold the raw edge of the binding towards the back of the potholder to make a loop. Stitch a zig-zag stitch back and forth over the raw edge to attach the loop.![Block to Potholder Binding _2.6.1]()
The potholder is finished!![Finished Potholders]()
Here are some other potholders:![Pen and Paper Finished Potholders]()
We hope you enjoyed learning how to turn orphan blocks, panel quilt blocks, or paper-pieced quilt blocks into a potholder.
![Chris's Signature]()
PRINTABLE PDF TUTORIAL -
If you would like an ad free printable version of this tutorial optimized for printing, please visit our
Etsy Shop listing for Turn a Quilt Block into a Potholder #ad.
For a small fee, you can purchase a PDF downloadable version of this tutorial.
QUESTIONS?
If you have any questions about this project, contact us through the YouTube Video
comments or our Contact Us page. We respond to questions in e-mails and YouTube comments regularly.
Some other potholder tutorials: